- - [ ] locate materials
- - [ ] 1x arduino
- - [ ] 1x deck
- - [ ] 4x spacers
- - [ ] 4x 6-32x5/8 inch bolt
- - [ ] 1x 6-32 nut
- - [ ] locate tools
- - [ ] safety goggles
- - [ ] magnetic tray
- - [ ] 5/64 inch hex wrench
- - [ ] pliers
- - [ ] drill
- - [ ] drill bit
- - [ ] drill 1 hole, put in 1 bolt
- - [ ] drill second hole, furthest away from first hole, put in 2nd bolt
- - [ ] drill 2 remaining holes
- - [ ] loosen first 2 bolts until arduino comes off
- - [ ] put in all 4 bolts just enough to place spacers on them
- - [ ] put arduino on top and tighten all but bottom right bolt
- - [ ] hold locking nut with pliers, shiny side toward arduino, while
- tightening last bolt into it.
+ - [ ] watch "02 arduino to deck intro"
+ - [ ] remove sonar sensors from deck if they're still attached
+ - [ ] watch "02 why drill" and "02 size bit, tighten teeth"
+ - [ ] locate material, from bag "2. arduino to deck"
+ - [ ] 1x arduino
+ - [ ] figure out what size drill bit to use
+ - [ ] make holes and put in bolts
+ - [ ] drill first hole
+ - [ ] locate materials, from bag "2. arduino to deck"
+ - [ ] 1x deck
+ - [ ] 1x arduino
+ - [ ] locate tools
+ - [ ] safety goggles
+ - [ ] magnetic tray
+ - [ ] drill
+ - [ ] drill bit
+ - [ ] watch "02 drill first hole"
+ - [ ] make sure arduino is in correct place and orientation
+ - [ ] drill through hole near arduino's reset button
+ - [ ] place first bolt
+ - [ ] locate materials
+ - [ ] 1x 6-32 bolt
+ - [ ] locate tools
+ - [ ] magnetic tray
+ - [ ] allen wrench
+ - [ ] put bolt up through bottom of deck into arduino,
+ tighten with allen wrench
+ - [ ] drill second hole
+ - [ ] locate materials
+ - [ ] safety goggles
+ - [ ] 1x 6-32 bolt
+ - [ ] locate tools
+ - [ ] drill
+ - [ ] drill bit
+ - [ ] deck with arduino on it
+ - [ ] watch "02 drill second hole"
+ - [ ] drill through hole furthest away from first hole
+ - [ ] place second bolt
+ - [ ] use allen wrench to put bolt up through the bottom of the
+ deck into the arduino
+ - [ ] drill remaining holes
+ - [ ] drill remaining 2 holes
+ - [ ] remove arduino, watch "02 remove arduino"
+ - [ ] undo the first 2 bolts until the arduino comes off
+ - [ ] put bolts into all 4 drilled holes
+ - [ ] watch "place spacers on bolts
+ - [ ] tighten bolts until they stick out the top of the deck
+ enough to put spacers on them
+ - [ ] place spacers on them
+ - [ ] place arduino on top
+ - [ ] tighten 3 bolts
+ - [ ] watch "02 tighten first 3 bolts"
+ - [ ] tighten the bolt near the reset button until head of bolt
+ is flush with bottom of deck.
+ - [ ] tighten the 2 bolts nearest the first bolt
+ - [ ] put the lock nut on
+ - [ ] locate materials
+ - [ ] 6-32 locknut
+ - [ ] locate tools
+ - [ ] pliers
+ - [ ] 5/64 allen wrench
+ - [ ] watch "explain locknut" and "02 tighten locknut"
+ - [ ] hold locknut over last bolt with pliers and tighten
+ it from below with allen wrench